Showing 3537–3552 of 5526 results
Group Marker Holders are available for identification of Terminal Block assemblies GMH6 can be mounted directly on Din Rails. A sticker / paper needs to be inserted in the slot which is covered by a transparent plastic sheet. Specification Height 46.5 mm Length 44.5 mm Width (Thickness) 9.5 mm Quantity 1 Pcs Country of Origin…
Group Marker Holders are available for identification of Terminal Block assemblies GMH6 can be mounted directly on Din Rails. A sticker / paper needs to be inserted in the slot which is covered by a transparent plastic sheet. Specification Height 46.5 mm Length 44.5 mm Width (Thickness) 9.5 mm Quantity 5 Pieces Country of Origin…
The Connectwell ODL2.5A is a 2.5 sq. mm 2 Level Offset stackable type Terminal Block in Grey color. The top level of the ODL2.5A Terminal Block is offset from the bottom level by half the terminal block’s thickness. While the wires are connected, this allows for easier access to the bottom-level screw. End Plates should be used at…
The complete Terminal Block assembly is kept in place on the Din Rail with the aid of End Clamps. On both sides of the Terminal Block assembly, End Clamps must be fixed.These end clamps are made to attach to rails that are DIN 32 and DIN 35. End clamps from the Polyamide series contain appropriate…
The complete Terminal Block assembly is kept in place on the Din Rail with the aid of End Clamps. On both sides of the Terminal Block assembly, End Clamps must be fixed.These end clamps are made to attach to rails that are DIN 32 and DIN 35. End clamps from the Polyamide series contain appropriate…
The Connectwell PTB35/50 is a 50 mm² Feed Thru Barrier Type Bolt Terminal BLOCK. PTB series Terminal Blocks are recommended for applications involving large cross-section wires. The wire is crimped to a ring/fork lug and screwed onto the Terminal Block’s flat current bar. Specially designed Mounting Feet secure the Terminal Block to the Mounting Rail. Two Lugs…
The Connectwell PTB35/50 is a 50 mm² Feed Thru Barrier Type Bolt Terminal BLOCK. PTB series Terminal Blocks are recommended for applications involving large cross-section wires. The wire is crimped to a ring/fork lug and screwed onto the Terminal Block’s flat current bar. Specially designed Mounting Feet secure the Terminal Block to the Mounting Rail. Two Lugs…
The Connectwell PTB70/95 95 mm² is a Feed Thru Barrier Type Bolt Terminal Block. PTB series Terminal Blocks are recommended for applications involving large cross-section wires. The wire is crimped to a ring/fork lug and screwed onto the Terminal Block’s flat current bar. The Terminal Block is held rigidly on the Mounting Rail by specially designed Mounting…
The Connectwell PTB70/95 95 mm² is a Feed Thru Barrier Type Bolt Terminal Block. PTB series Terminal Blocks are recommended for applications involving large cross-section wires. The wire is crimped to a ring/fork lug and screwed onto the Terminal Block’s flat current bar. The Terminal Block is held rigidly on the Mounting Rail by specially designed Mounting…
The Connectwell STH4DTSH is a Hinge Type Disconnect and Test Shorted Terminal Block. STH4DTSH 6 mm² M4 Stud Disconnect & Test shorted Terminal Block – with captive nuts. These Terminal Blocks are recommended for applications in which the connections are subjected to high vibrations. The wire is crimped to a ring/fork type Lug (Ferrule) and screwed onto the…
This small continuity tester with pen probe has a built-in LED that lights up when it is continuous conductivity between the two probe terminals. It is simple to use this continuity tester. Features: Its continuity tester Its used in hardware Debugging Its used in PCB repairing Specification Brand Generic Power Supply LR1130 Battery Powered (Batteries…
This is a Micro USB STM8S103F3P6 Development Board that uses Micro USB for power and communication with programmers. This Development Board has an 8-bit microcontroller from ST Microelectronics STM8S103F3P6 is a rugged, high performance microcontroller unit with UART, I2C, SPI, and a 5-channel 10-bit ADC. It supports SWIM debug mode. In their inbuild components: MicroUSB input, Reset button, IC and LED indicators. Features Indicator LEDs Minimum System Board Micro USB line is compatible Note: 5V-Pin is an…
This Module is CP2102 it has total 5 pins which is used in to make serial communication Between USB to TTL UART, its a serial Converter module. This module has an IC CH9102 is a USB bus converter chip, which converts USB to serial UART interface. CH9102 provides common MODEM signal, to expand UART interface of…
CPGXLD 9700 series thermal protector consists of dish shape high sensitive bimetallic element, movable contact-head, static contact-piece, thermal resistant lead and so on. When an electric appliance is in operation, the bimetallic element is in a free state and the movable contact head and static contact piece are closed and the circuit is on. When…
The CR1220 3V-Lithium Coin Battery is a Small, portable electronic devices such as keyless entry remotes, laser pointers, pocket calculators, implantable cardiac defibrillators, and even artificial cardiac pacemakers are powered by mounting, button, and coin cell batteries. Its diameter is 12.5mm, and its thickness is 2.3mm. Features: It’s used for small power electronic gadgets Small in…
It’s a 3v Lithium coin cell battery. It has nominal voltage 3v and rated capacity 560mAh. This battery can operate on temperature range -30°C to 60 °C. This battery generally used for memory back-up, digital watches, car keys, laser pen, fitness appliances and medical devices such as tensiometer and clinical thermometer. Features Type Coin Cell Model CR2016…