1 Channel 5V Solid State Relay Module
₹117.00NOT AVAILABLE
Showing 1–16 of 42 results
-
-
1 Channel IR Relay Control Module With Range Adjuster
₹239.00This is an IR Detector Single Channel Relay Control Module with Range Adjuster. The operating current of this module is 5V DC; hence 5V is supplied to the Vcc. GND is connected to the ground of the system. Out pin gives an active high output when any obstacle is detected. A potentiometer is also there…
-
12V 10A Single Channel Relay Module with Optocoupler
₹79.0012V 1-Channel Relay module is able to control various appliances and other equipment with a large current. It can be controlled directly by a Micro-controller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). Features LED Status indicator High-quality screw terminals Mounting Holes Freewheeling Diode to protect your microcontroller Optocoupler to isolate the microcontroller…
-
12V 16 Channel Relay Module with Light Coupling LM2596 Power Supply
₹528.00This is a 12V 16 Channel Relay Module with a Light Coupling LM2596 Power Supply that can control a wide range of appliances and other high-current devices. Microcontrollers (Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic) can be used to control it directly. This is a 12V 16-Channel Relay Interface Board with 15-20mA Driver Current…
-
12V 30A T Type Power Relay H90-S-DC12V-C
₹47.00This Power relay is used for switching high current AC appliances such as Air Conditioner, Electric Heater, Geyser etc. which need to be controlled from microcontroller or sensor output. 12V T Type Relay can switch load of 30A connected to it. There are 6 Pins in this relay which are shown in the image. The relay we…
-
12V 4 Channel Relay Module with Optocoupler
₹178.0012V 4-Channel Relay module is able to control various appliances and other equipment with a large current. It can be controlled directly by a Micro-controller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). Features LED Status indicator High-quality screw terminals Mounting Holes Freewheeling Diode to protect your microcontroller Optocoupler to isolate the microcontroller…
-
12V 8 Channel Relay Module with Optocoupler
₹325.00This is an 8-channel relay board that runs on 12 volts. Any microcontroller or other control system circuits can be used to control loads rated up to 250V 10A AC directly. Each relay has three connections: Common (C), Normally Open (NO), and Normally Closed (NC), all of which are connected to three-pin screw terminals, making it…
-
12V Modbus RTU 4 Way Relay Module with STM8S003F3P6 RS485 Communication
₹617.00Relay communication: Multi-unit network 485 communication, based on MODBUS-RTU protocol, the default communication address is 1, users can modify the address by instructions IN1-IN4 are connected to the switch. The switch status is read through 485, not through the input control relay output. Specification Operating Voltage 12V DC Switching Capacity AC 250V @10A, DC 30V…
-
-
-
2 Channel 5V Relay Module
₹70.00This 2 Channel 5 Volt Relay Module. The triggering of this 2 Channel Relay Module is reliable and more stable. It has power and relay operation instructions. Relays terminals (C, NC, NO) are accessible through screw terminals. It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. Features Making wiring up the board…
-
-
-
24V 10A Single Channel Relay Module with Optocoupler
₹67.0024V 1-Channel Relay module is able to control various appliances and other equipment with a large current. It can be controlled directly by a Micro-controller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). Features LED Status indicator High-quality screw terminals Mounting Holes Freewheeling Diode to protect your microcontroller Optocoupler to isolate the microcontroller…
-
24V 16A Small High Power AC Relay
₹109.00This Small High Power AC Relay is a miniature power relay. The coil on this relay is rated for up to 24V and has a switching capacity of 16A. Relay contacts are rated up to 16A @250VAC/24VDC. Datasheet Specification Switching Voltage 250V Coil Voltage 24V DC Contact Current Rating 16A Mounting PCB Through Hole Contact Material AgSnO2…
-
24V 8 Channel Relay Module with Optocoupler
₹461.00This is an 8-channel relay board that runs on 24 volts. Any microcontroller or other control system circuits can be used to control loads rated up to 250V 10A AC directly. Each relay has three connections: Common (C), Normally Open (NO), and Normally Closed (NC), all of which are connected to three-pin screw terminals, making it…