Showing 545–560 of 5526 results
It’s a 12V 5A SMPS Power Supply Circuit Board. This 12V 5A power supply is mainly used in‚ chargers‚ microcontrollers‚ portable amplifiers‚ audio-video players‚ Bluetooth/wifi modules‚ DC motors‚ and led light circuits. Despite being small in size this power supply work effectively. The input voltage of this supply is 220VAC and the output is 12V DC. This…
Chip-on-Board (COB) LEDs is actually an array of high-power LED that is created by placing many low-wattage (typically 0.5W or 1W) LED dies side-by-side on a circuit board. COB LEDs are brighter, consume less power, and output a higher quality beam of light compared to older LED Specification Operating Voltage 12V DC Max. Operating Current 410mA Power 5W Glow…
This is a High-Quality 60x60x15mm Cooling Fan. The cooling fan comprising of a 4-pole Brushless DC Motor with a precise vapo bearing system, this cooling fan can deliver a decent airflow, which is sufficient enough to keep the electronics cool. It can be used with CPU, 3D printers, and other electronic systems. Features Rated voltage:…
LM75-22B12 is one of Mornsun’s enclosed AC-DC switching power supplies. It has dual or reinforced insulation, low no-load power consumption, high efficiency, high reliability, and AC input while also accepting DC input voltage. This power supply is also cost-effective. The IEC/EN61000-4, CISPR32/EN55032, IEC/UL/EN62368, EN60335, and GB4943 standards are met by these converters, which also exhibit excellent EMC…
This is an 8-channel relay board that runs on 12 volts. Any microcontroller or other control system circuits can be used to control loads rated up to 250V 10A AC directly. Each relay has three connections: Common (C), Normally Open (NO), and Normally Closed (NC), all of which are connected to three-pin screw terminals, making it…
LM100-20Bxx series is one of Mornsun’s enclosed AC-DC switching power supplies. It features universal AC input and at the same time accepts DC input voltage, is cost-effective, low no-load power consumption, high efficiency and high reliability. These converters offer excellent EMC performance and meet IEC/EN61000-4, CISPR32/EN55032, IEC/EN/UL62368, EN60335, GB4943, EN61558 standards and they are widely…
It’s a 12v dc solar powered submersible water pump. Its Uses advanced electronic components and high-quality wear-resistant shaft. It has Smooth operation, high efficiency, good performance, long service life This Can be a long time continuously work, low noise, safety and environmental protection. It is Widely used in Aquarium, Fish Pond, Industry, Scientific research, Aerospace…
This solenoid valve allows users to adjust the water flow. It’d be a fantastic addition to robotic gardening projects. The valve is normally closed. The solenoid coil controls the valve electronically with a DC 12 volt supply. It opens the flow of fluids as soon as it is switched on and stops/blocks the flow when…
The DC 12V 2W white Big Tube COB(chip-on-board) High Brightness Waterproof Injection Module With Diffused Lens is mostly used for decorating and inside advertising lightboxes to illuminate alphabets and brand logos. This item also includes a 3M Foam tape on the back, which will allow the buyer to attach it to the desired application location…
The DC 12V 2W Blue Big Tube COB(chip-on-board) High Brightness Waterproof Injection Module With Diffused Lens is mostly used for decorating and inside advertising lightboxes to illuminate alphabets and brand logos. This item also includes a 3M Foam tape on the back, which will allow the buyer to attach it to the desired application location…
The DC 12V 2W Green Big Tube COB(chip-on-board) High Brightness Waterproof Injection Module With Diffused Lens is mostly used for decorating and inside advertising lightboxes to illuminate alphabets and brand logos. This item also includes a 3M Foam tape on the back, which will allow the buyer to attach it to the desired application location…
The DC 12V 2W Red Big Tube COB(chip-on-board) High Brightness Waterproof Injection Module With Diffused Lens is mostly used for decorating and inside advertising lightboxes to illuminate alphabets and brand logos. This item also includes a 3M Foam tape on the back, which will allow the buyer to attach it to the desired application location…
The DC 12V 2W White Big Circle COB(chip-on-board) High Brightness Waterproof Injection Module With Diffused Lens is mostly used for decorating and inside advertising lightboxes to illuminate alphabets and brand logos. This item also includes a 3M Foam tape on the back, which will allow the buyer to attach it to the desired application location…
The DC 12V 2W Pink Big Tube COB(chip-on-board) High Brightness Waterproof Injection Module With Diffused Lens is mostly used for decorating and inside advertising lightboxes to illuminate alphabets and brand logos. This item also includes a 3M Foam tape on the back, which will allow the buyer to attach it to the desired application location…
The DC 12V 2W Red Big Tube COB(chip-on-board) High Brightness Waterproof Injection Module With Diffused Lens is mostly used for decorating and inside advertising lightboxes to illuminate alphabets and brand logos. This item also includes a 3M Foam tape on the back, which will allow the buyer to attach it to the desired application location…
The DC 12V 2W white Big Tube COB(chip-on-board) High Brightness Waterproof Injection Module With Diffused Lens is mostly used for decorating and inside advertising lightboxes to illuminate alphabets and brand logos. This item also includes a 3M Foam tape on the back, which will allow the buyer to attach it to the desired application location…