Showing 5201–5216 of 5526 results
Its TIP32C PNP Bipolar Power Transistor 100V 3A TO-220. TIP32C is a silicon Epitaxial-base PNP power transistor packaged in a Jedec TO-220 plastic packaging. It’s designed for medium-power linear and switching applications. TIP31C is the complementary NPN type. Specifications: Type PNP Transistor Collector-Emitter Voltage 40 VDC Collector-Base Voltage 40 VDC Continuous Collector Current 3 ADC Continuous…
The TIP42C is a -100V PNP complementary silicon plastic Power Transistor designed for use in general purpose power amplifier and switching applications. Its used in Switching applications Like in general switching, snubber circuits, clamp, Inverter and many other circuits. Specifications Part Number TIP42C Type PNP Transistor Collector-Emitter Voltage 40V DC Collector-Base Voltage 40V DC Continuous Collector…
TK12A600 is a N-Channel MOSFET with the best combination of fast switching, ruggedized device design, low on-resistance, and cost-effectiveness. The TO-220 package is universally preferred for all commercial-industrial applications. Features Low drain-source ON resistance: RDS (ON) = 0.45 Ω (typ.) High forward transfer admittance: ⎪Yfs⎪ = 7.5 S (typ.) Low leakage current: IDSS = 10 μA…
These monolithic integrated circuits with low-noise JFET input operational amplifiers combine two cutting-edge analogue technologies. Each internally corrected operational amplifier features a well-matched high-voltage JFET input device for low input offset voltage. BEFIT technology’s low supply, input offset, and bias currents make wide bandwidths and quick slew rates possible. The devices also have minimal harmonic…
The TL431 is a three-terminal adjustable regulator series with guaranteed thermal stability over the temperature ranges applicable. With the help of two external resistors, the output voltage can be adjusted to any value between VREF (approximately 2.5 volts) and 36 volts. The typical dynamic output impedance of these devices is 0.2. Because active output circuitry has…
The TL494 is a fixed frequency, pulse width control circuit IC designed primarily for switched-mode power supply. Features Complete Pulse Width Modulation Control Circuitry On-Chip Oscillator with Master or Slave Operation On-Chip Error Amplifiers On-Chip 5.0 V Reference Adjustable Deadtime Control Uncommitted Output Transistors Rated to 500 mA Source or Sink Output Control for Push-Pull…
The user interface is well-designed and is in complete accord with the operating habit of the Windows series of software. The built-in binary editor is comparable to pure professional editing software. You can directly read, write and modify the files such as BIN format, HEX format, JED format and so on. In addition, it has…
The HS CAN-transceivers of the TLE6250 family are monolithic integrated circuits and they are optimized for high speed differential mode data transmission in automotive applications and industrial applications. The TLE6250 is designed to withstand the severe conditions of automotive applications and provides excellent EMC performance. The transceivers work as an interface between the CAN protocol…
The HS CAN-transceivers of the TLE6250 family are monolithic integrated circuits and they are optimized for high speed differential mode data transmission in automotive applications and industrial applications. The TLE6250 is designed to withstand the severe conditions of automotive applications and provides excellent EMC performance. The transceivers work as an interface between the CAN protocol…
TLP620-4 is a 16 pin optocoupler IC having four isolated channel as we know that the optocoupler contains photo diode and infrared diodes too so this photocoupler contains photo diode and infrared diode. Optocoupler is used to provide coupling between two isolated circuit it also works as a circuit protector too. Its maximum current transfer ratio…
The TM1637 is a 7-segment 4-digit display that can be easily controlled by an Arduino with a few wires. There are 12 pins on a 4-digit, 7-segment LED display. 8 of the pins are for the 8 LEDs on a 7-segment display (A-G and DP) (decimal point). The remaining four pins correspond to the four digits…
The Metal Oxide Varistor (MOV) is a component that is used in electrical circuits to limit voltage. They’re mostly found in voltage-sensitive electrical gadgets’ protection circuits. A varistor effectively bypasses all transient surge voltages. A varistor is a voltage-dependent‚ nonlinear device that behaves similarly to back-to-back Zener diodes in terms of electrical behavior. Zinc oxide…
The TNY268 integrates a 700 V power MOSFET, oscillator, high voltage switched current source, current limit, and thermal shutdown circuitry onto a monolithic device IC. The start-up and operating power are derived directly from the voltage on the DRAIN pin, eliminating the need for a bias winding and associated circuitry. In addition, the TNY268 device incorporates auto-restart,…
TNY277PN is a type of IC this IC has 7 pin its a tiny switch IC in which one pin is not present its trough hole components. It has manufactured by Power integration. Tiny Switch-III combines a high-voltage power MOSFET switch with a power supply controller in one device. Unlike conventional PWM (pulse width modulator)…
TNY280PN AC/DC Off-Line Switcher Converter from PDIP-8 IC Package. TinySwitchTM-III is an energy-efficient offline switcher with increased flexibility and a wider power range. consists of a 700V power MOSFET, an oscillator, a high-voltage switched current source, a current limit (user selectable), and thermal shutdown circuitry. The IC family uses an ON/OFF control scheme and provides…
8051 USB Programmer is used for the 8051 micro-controller family. It is a very powerful and low-cost programmer. It is powered by a USB and does not need any external power source. It comes with a user-friendly GUI and power and status indicator LEDs. Download CD from here Specification Model TOP8051 Batch 2020 Power Self…