Showing 97–112 of 195 results
The LM358 is a dual op-amp IC that integrates two op-amps that are powered by a single power supply. It is one half of the LM324 Quad op-amp, which contains four op-amps with a shared power supply. The differential input voltage range can be the same as the power supply voltage range. The default input…
This amplifier module is based on the LM358 operational amplifier, which is a high-gain, frequency adjusted operational amplifier designed to operate across a wide voltage range from a single power source. It is utilised in standard operational amplifier circuits that require a single power rail to function. Features: 100 gain of the circuit design. 10K…
The LM386 is power amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but the addition of an external resistor and capacitor between pins 1 and 8 will increase the gain to any value from 20 to 200. The inputs are ground referenced…
The LM3914 is a monolithic integrated circuit that detects analog voltage levels and operates ten LEDs to create a linear analog display. With a single pin, the display transforms from a moving dot to a bar graph. The LEDs’ current drive is regulated and customizable, removing the need for resistors. This is a feature that…
The LM393 is made up of two independent precision voltage comparators with offset voltage specifications as low as 2.0 mV max for two comparators that were especially intended to work from a single power supply over a broad variety of voltages. It is also feasible to operate from split power supplies, and the low power…
The LM833 is a monolithic dual operational amplifier that is particularly well suited for audio applications. It features high frequency performance (15MHz Gain Bandwidth product, 7V/s slew rate), low voltage noise (4.5nV/Hz), and low voltage noise.The LM833 also has good phase/gain margins and very low distortion (0.002 percent). Features ESD protection 2kV Low voltage noise:…
LT1013 is the first precision dual op-amp in the 8-pin industry standard configuration, upgrading the performance of such popular devices as the MC1458/1558, LM158 and OP-221. The LT1013’s specifications are similar to (even somewhat better than) the LT1014’s. Both the LT1013 and LT1014 can be operated off a single power supply: input common-mode range includes…
The MAX485 is a low-power transceiver that supports RS-485 and RS422 communication. The integrated circuit has one driver and one receiver. The MAX485 driver slew rates are not limited, allowing them to transmit up to 2.5Mbps. When empty or fully loaded with deactivated drivers, these transceivers demand between 120A and 500A of supply current. All…
The MAX487 is a low-power transceiver for RS-485 and RS422 communication. One driver and one receiver are present in each component. The MAX487 has decreased slew-rate drivers that reduce reflections from incorrectly terminated cables and limit EMI, enabling error-free data transmission at speeds of up to 250kbps. MAX1487 is not limited, allowing them to transmit…
The MAX487 is a low-power transceiver for RS-485 and RS422 communication. One driver and one receiver are present in each component. The MAX487 has decreased slew-rate drivers that reduce reflections from incorrectly terminated cables and limit EMI, enabling error-free data transmission at speeds of up to 250kbps. MAX1487 is not limited, allowing them to transmit…
MC14021B 8−bit static shift registers are constructed with MOS P−channel and N−channel enhancement mode devices in a single monolithic structure. These shift registers find primary use in parallel−to−serial data conversion, synchronous and asynchronous parallel input, serial output data queueing; and other general-purpose register applications requiring low power and/or high noise immunity. Features Asynchronous Parallel Input/Serial…
MC33172 is a monolithic op-amp in which high-quality bipolar fabrication and unique design principles are used. Without the usage of JFET device technology, these devices run at 180 A per amplifier and provide a gain-bandwidth product of 1.8 MHz and a slew rate of 2.1 V/s. Although this series can be run from split supplies,…
MC33172 is a monolithic op-amp in which high-quality bipolar fabrication and unique design principles are used. Without the usage of JFET device technology, these devices run at 180 A per amplifier and provide a gain-bandwidth product of 1.8 MHz and a slew rate of 2.1 V/s. Although this series can be run from split supplies,…
MCT2E Optocoupler uses infrared LED and a silicon NPN phototransistor. It’s a six-pin DIP optoisolator/optocoupler. The MCTE is a single channel photo transistor that is industry standard. Each optocoupler is made up of an infrared LED made of gallium arsenide and a silicon NPN photo transistor. Underwriters Laboratories (UL) has listed these couplers to meet a…
The ATmega168PA is a low power, CMOS 8-bit microcontroller based on the AVR® enhanced RISC architecture. By executing instructions in a single clock cycle, the devices achieve CPU throughput approaching one million instructions per second (MIPS) per megahertz, allowing the system designer to optimize power consumption versus processing speed. The high-performance Microchip Pico Power® 8-bit AVR® RISC-based microcontroller combines…